1972 Chevrolet Blazer Leaf Helper Spring Parts
Choose your Engine for your 1972 Chevrolet Blazer
Image
Product
Price
- Up To 2000 lbs. Level Load Capacity Will Not Fit with Rear A.C.
- EZ-990 Helper Spring Kit for Dodge; Ford; GM; Toyota
- EZ-990 Helper Spring Kit
- Product Attributes:
- Mounting Hardware Included: Yes
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Adjustable Length: Yes
-
Features:
- Adjusted Independently For Uneven Side To Side Loads
- Mount Under Factory Axle U-Bolt Plates
- Complete Bolt On Installation
- Variable Rate Leaves Do Not Effect Ride When Unloaded
- Adds New Life To Old Springs
- Reduces Body Roll
- High Quality Spring Steel Leaves
- Limited Lifetime Warranty
- Hellwig's medium-duty EZ-990 Helper Springs pack a lot of capability in every box. Packaged complete with the same heavy duty powder coated and plated components, hardware and installation instructions as our heavy duty helper spring products, these kits are designed for the vehicles that need lighter assistance in carrying a load. Simple bolt on design using common hand tools provide the installer ease of installation and the vehicle owner hassle free use. Ideally suited for light towing and loads, these units are fully adjustable using the heavy duty U-bolts included in the kit using simple hand tools. If your tow and haul needs change, simply adjust the heavy duty U-bolts to suit the new load requirements. Once installed and adjusted you are free to haul or tow with greater control and stability. Manufactured with heat treated ASTM 5160 alloy spring steel in our California based facility, these units are rated up to 2,000 lb. level load carrying capacity. They are a great cost effective spring solution and can be adjusted independently for uneven side to side loads.
Additional Fitment Information:
| Vehicle |
|---|
| 1972 - Chevrolet Blazer |
- 1969-1998 Chevy Truck 1/2/3/4 ton-Rear 2in. Add-a-Leafs Pair
- 2 in.; Includes Center Pins; Pair
- 1969-1998 Chevy Truck 1/2/3/4 ton-Rear 2in. Add-a-Leafs Pair
- Add-A-Leaf Kit
- Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer And Birth Defects Or Other Reproductive Harm. For More Information: Www.p65warnings.ca.gov
-
Features:
- Mounts To Existing Leaf Springs
- Economical Method Of Lifting Vehicle w/Leaf Springs
- Increases Payload Capacity
- Center Pins Included
- Great For Vehicles w/Winches Or Snowplows
- Tuff Country add-a-leafs are an economical solution to lifting vehicles with leaf springs. These add-a-leafs are designed to be added to existing stock leaf springs to give a small amount of additional height or lift to your vehicle and gain additional payload capacity.
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 1972 - Chevrolet Blazer | Rear | 4WD |
- 1969-1998 Chevy Truck 1/2/3/4 ton-Rear 2in. Add-a-Leafs Pair
- 2 in.; Includes Center Pins; Pair
- 1969-1998 Chevy Truck 1/2/3/4 ton-Rear 2in. Add-a-Leafs Pair
- Add-A-Leaf Kit
- Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer And Birth Defects Or Other Reproductive Harm. For More Information: Www.p65warnings.ca.gov
-
Features:
- Mounts To Existing Leaf Springs
- Economical Method Of Lifting Vehicle w/Leaf Springs
- Increases Payload Capacity
- Center Pins Included
- Great For Vehicles w/Winches Or Snowplows
- Tuff Country add-a-leafs are an economical solution to lifting vehicles with leaf springs. These add-a-leafs are designed to be added to existing stock leaf springs to give a small amount of additional height or lift to your vehicle and gain additional payload capacity.
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 1972 - Chevrolet Blazer | Rear | 4WD |
- ADD-A-LEAFS FRT 67-87 GM
- Lift Height 1.5-2 in.; w/Tie Bolts; Pair
- FRT ADD-A-LEAFS CHEVY;DODGE
- Softride Add-A-Leaf
- Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: California Residents- Warning: Cancer And-or Other Reproductive Harm. (for More Information Go To Www.p65warnings.ca.gov)
-
Features:
- Constructed As Progressive Multileaf Packs
- Load Capacity Will Be Equal or Greater Than OE
- Made With American Steel
- Limited Lifetime Warranty
- Softride(R) Add-a-leafs use only American steel and are shot-peened with hard steel pellets at very high velocities. This shot-peening compresses the surface of the steel thereby increasing the tensile strength of the leaf. Without this shot-peening procedure, the maximum wheel travel and ride quality could not be achieved without sacrificing the life of the leaf. The Skyjacker(R) add-a-leafs are pre-drilled for the center pin. Pin location varies with each application. Most have long tapered ends for a progressive affect and ride comfort.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Drive Type | CID |
|---|---|---|---|---|---|---|
| 1972 - Chevrolet Blazer | V | 5031 | Front | 8 Cyl 5.0L | 4WD | 307 |
- Up To 2000 lbs. Level Load Capacity; Step Bracket Style
- EZ-990 Helper Spring Kit-Step Bracket Style Leaf 2.5in.
- EZ-990 Helper Spring Kit
- Product Attributes:
- Mounting Hardware Included: Yes
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Adjustable Length: Yes
-
Features:
- Adjusted Independently For Uneven Side To Side Loads
- Complete Bolt On Installation
- Variable Rate Leaves Do Not Effect Ride When Unloaded
- Adds New Life To Old Springs
- Reduces Body Roll
- High Quality Spring Steel Leaves
- Limited Lifetime Warranty
- Hellwig's medium-duty EZ-990 Helper Springs pack a lot of capability in every box. Packaged complete with the same heavy duty powder coated and plated components, hardware and installation instructions as our heavy duty helper spring products, these kits are designed for the vehicles that need lighter assistance in carrying a load. Simple bolt on design using common hand tools provide the installer ease of installation and the vehicle owner hassle free use. Ideally suited for light towing and loads, these units are fully adjustable using the heavy duty U-bolts included in the kit using simple hand tools. If your tow and haul needs change, simply adjust the heavy duty U-bolts to suit the new load requirements. Once installed and adjusted you are free to haul or tow with greater control and stability. Manufactured with heat treated ASTM 5160 alloy spring steel in our California based facility, these units are rated up to 2,000 lb. level load carrying capacity. They are a great cost effective spring solution and can be adjusted independently for uneven side to side loads.
Additional Fitment Information:
| Vehicle |
|---|
| 1972 - Chevrolet Blazer |
Showing 1 - 5 of 5 products
Loading...